10,000 lb. Capacity EXTENDED Symmetric Standard 2 Piece Front & Rear Arms


  • Stronger and more stable structure - up to 20% heavier than many competitors. Two (2)” / 51mm reinforcement tubes are welded inside the 11” x 7” with 1/4” wall / 279mm x 178mm with 6mm wall columns to provide better stability with heavier loads.
  • Corrosion resistant protection - steel components are wheel-a-brator shot blasted and acid washed before a “double bake” powder coat finish is applied.
  • Lifts higher to provide more under car work area - the 70-1/2’” / 1791mm long cylinder stroke provides 76” / 1930mm lift without adapters with a maximum attainable lift height of 87” / 2210mm.
  • Flexible vehicle loading - Flexmetric arm design uses three (3) piece “offset” front and straight (3) piece rear lifting arms for optimum asymmetric and symmetric loading opportunities.
  • Reduced installation costs - field adjustable height and width can easily adapt to most installation dimensions. Premium North American Components - North American made Bucher 2HP / 1.5kw power unit, 3/8”/ 9.5mm equalizing cables and 2” / 51mm ID hydraulic cylinders provide longer more dependable service life.
  • Reduced vehicle setup time - Acme screw “drop in” style lift pads have a lowered height with rubber pad of 4” / 102mm and can be extended by 1-1/2” / 38mm, 3” / 76mm or 6” / 152mm using nickel plated drop in adapters. Power unit can be installed on either column.
  • Quieter operation less than <75 decibels - rubber mounting grommets reduce power unit noise. Car door protection - 11” x 2” /279mm x 51mm rubber door bumpers are mounted on the face of both lifting carriages to reduce door damage.
  • More models to chose from - standard Flexmetric design with 3 piece lifting arms, symmetric version with equal length straight arms, extended height 172” / 4389mm and choice of red or blue.


Three piece, offset arms front and rear for asymmetric and symmetric loading Three piece, offset arms front and rear for asymmetric and symmetric loading	  Height adapters #TLS2PTA4-2 Height adapters #TLS2PTA4-2
Drop in screw adjustment style lifting pads Drop in screw adjustment style lifting pads	3/8" / 9.5mm non-fatigue cables with 3-1/2" / 89mm pulleys 3/8” / 9.5mm non fatigue cables with 3-1/2” / 89mm pulleys
2" / 51mm tube column reinforcement 2” / 51mm tube column reinforcement	Single point lock release Single point lock release


Capacity 10,000 lb. / 4.5T
Overall Height 172" / 4368mm
Under Bar Clearance (Field Asjustable) 131" or 141" / 3505mm or 3759mm
Overall Width 135-1/2" / 3429mm
Width Between Columns 112-3/4" / 2845mm
Drive Thru Width 92" / 2337mm - symmertric 100”/ 2540mm
Height to Lowered Lift Pad 4" / 102mm
Raised Height with Standard Pad 76" / 1930mm
Raise Height with Adapters 87" / 2210mm
Lifting Time 55 seconds
Front Arm Reach 19-3/4" to 42" / 502mm to 1067mm - Symmetric 35” to 60” / 889mm to 1524mm
Rear Arm Reach 35" to 60" / 889mm to 1524mm
Standard Power Requirements 220 Volts - 50/60 Hz - 1 PH - 20amp
Shipping Weight 1,980 lbs. / 900 kg.
Model: TLS210NRx1 Height as listed
Model: TLS210SRx1 Height as listed, Symmetric, Equal Arms
Model: TLS210NXx1 Extended Ht. 172” / 4370mm
Model: TLS210SXx1 Extended Ht. 172” / 4370mm Symmetric